Clone-A-Pussy Plus + Review

Personal Experience

My Previous Experience

As a previous anniversary present, my wife and I have completed both the Clone-A-Willy and Clone-A-Willy Plus+Balls kits with varying degrees of success. The initial process with the Clone-A-Willy Plus+Balls kit was a little overwhelming at first.  There are a lot of steps and the process is pretty extensive. Plus, while going through the process you have to time everything accordingly so that your member is at full attention when the time comes and he stays that way during the entire molding process.  Obviously, having a helper was invaluable during this process.  The finished product was … a little underwhelming, I’ll say. With the Plus+Balls kit you have to have a pretty good overall anatomy to have great success, and overall, it was very stressful. We decided we would give it another shot but this time use just the Clone-A-Willy kit and see how it goes. At this point we knew what we were getting into and we felt much better and tried to have a little more fun with everything. The results this time were much better and more what we were expecting.

My Current Experience with the Clone a Pussy

Having had previous experience with the Empire Labs line of products, we were excited to give this one a try!  We were able to produce a semi-respectable penile clone, and I was excited at the prospect of creating a personal, usable vaginal clone to add to my repertoire of masturbation sleeves.  The process was very similar to both the previous attempts barring a few minor changes. Obviously, there was no longer a penis sleeve but rather a cap shaped like a vulva. It used the same body-safe alginate molding powder and mix as well as the same two-part silicone mix.

Step 1

The initial setup involves getting the temperature right on water used to mix with the alginate molding powder. The 90 degree temperature seems high, but if you get too high or too low, that can really affect the drying time of the mold. Too high and it will dry too quickly, too low and it will dry too slow. So, we tried to get as close as possible. Some kits come with an included ethanol thermometer but we found this to be too inaccurate. We opted to use one of our kitchen thermometers instead, and were much happier with the readings.

Step 2

We poured the molding powder in our mixing bowl and slowly poured in the water. Then, we used a whisk to try and blend up as much of the powder as possible, trying to get as many of the lumps out while still trying to keep it smooth. The tiny air bubbles you incorporate while mixing can wreak havoc on the final product, so mix vigorously but with care, stirring for approximately 45 seconds.

Step 3

Once mixed, carefully pour the mixture into the cup and have your model place the cup onto their vulva. You will want to make sure to fill the cup up as much as possible to ensure that the entire area is covered. It will spill over so be prepared. It is also suggested to be in a location with harder floors.  Trying to remove any excess molding mix out of fabric/carpet would not be fun! Peeling it off of our vinyl bathroom floor was easy-peasy. Once in place, wait 2-4 minutes for the mold to set. It will be very obvious as the alginate will harden into a jelly like consistency.

Step 4

Once set you can remove the mold and place it into the cap at the end of the sleeve. Try to situate the mold to where it is even and flat.  If it isn’t, the final product could be lopsided and no one wants a lopsided pussy… I don’t think.

Step 5

Using the supplied ball wedge, slice the mold open with the wedge, trying to center it as much as possible. This will make the opening of the masturbator sleeve.  Once in place, proceed to the next step.

Step 6

You can now install the plastic sleeve housing onto the molding cup with the ball wedge in place.  This will act as the final mold for the replica.

Step 7

Carefully mix the supplied two-part silicone mix into a disposable cup and pour it into the bottom, open end of the sleeve housing.  Take extra care to limit the amount of silicone you get on the sides of the sleeve housing as this could limit the amount of silicone that actually makes it to the mold.

Step 8

Now you wait. I waited ~12 hours but the instructions say to wait a minimum of 8 hours. After that, you can carefully start to disassemble the sleeve. Take extra when removing the bottom lid as this has the mold and all the excess silicone, which could be hard to remove. Once you remove the lid, carefully remove your mold and revel in your craftiness!

Step 9

From here you will want to trim up your lovely pussy-clone, removing as much excess silicone as possible and making it look all nice and pretty.

Step 10

Now, you get to assemble everything.  Place the sleeve into the sleeve holder, making sure to push it as far down as possible.  Then you can insert your molded pussy onto the top of the sleeve holder.  There is a groove around the bottom of the mold that will fit right into the sleeve holder. Now you can marvel at what you just accomplished. It was no small feat. It was a bit stressful and time-consuming, but in the end I think it was worth it. Once finally assembled, you can actually use the completed sleeve!

Using the Masturbator

Once lubed up, my initial experience was odd. The harder silicone of the exterior mixed with the more flexible TPE of the internal sleeve made it hard to get fully inserted into. I found that by removing some of the material around the opening of the TPE sleeve, it was much easier to insert my penis and use. Once you get everything nice and lubed up, the experience goes about like you’d expect. The difference in texture and materials adds a welcome change to some of the other single material masturbators. The internal sleeve texture isn’t anything to write home about but it was satisfactory enough. Overall, I’m extremely happy with the end result of both the creation and testing of my personalized masturbator.